Port St. Lucie Tankless Water Heater logo
White outdoor tankless water heater mounted on a sand-colored stucco house wall with copper water lines and a gas line running down beside a palm

Tankless water heater in Port St. Lucie, FL

Tankless Water Heater Venting in Port St. Lucie, FL

  • Vent cost: HomeGuide's national figures put a first-time gas vent at $500 to $1,500 ($100 to $600 to replace an existing one); This Old House puts stainless venting at $400 to $800.
  • Time: HomeGuide's labor estimate for a full tankless install is 3 to 10 hours; the vent is part of that job.
  • Material: Florida's fuel gas code allows plastic vent only where the heater is listed for it; the maker's instructions set the rest.
  • Window rule: a direct-vent terminal on a unit above 150,000 Btu/h stays 4 feet or more from the side of, or below, an openable window or door.
  • Old flue: HomeGuide notes that the vent from an old gas tank heater won't serve a tankless unit.

Both price ranges are national, not local quotes. Port St. Lucie Tankless Water Heater, a free service, books a call-back from an independent plumber who can plan where the vent exits. Say where the heater will hang, which wall faces outside, and how close the nearest window is.

Tankless Vent Routes in Port St. Lucie Garages

Census figures show about 91% of Port St. Lucie homes heat with electricity, which hints that most never had a gas appliance to vent. So a gas tankless job here usually means cutting a new hole, not reusing one. Direct-vent units take their combustion air from outdoors and send flue gases out the same way, and Florida's fuel gas code hands the design of Category III and IV vents to the heater's maker.

New vent pipe passing through the block wall of a garage behind a freshly mounted gas tankless water heater, with the old electric tank removed

Adding a First Vent Where an Electric Tank Stood

An electric tank had no flue, so the plumber plans the vent from scratch: the shortest run to an outside wall, the fewest elbows, and a terminal spot that meets the clearances below. Rinnai's manual for its RL75i and RL94i lets the vent run 41 feet with no elbows, 35 feet with one and 29 feet with two. A heater can't share a vent with another appliance or tie into an old chimney.

  • Rinnai maximum vent length: 41 ft straight; each 90-degree elbow cuts 6 ft
  • No common venting with another appliance
  • No connection to an existing vent or chimney
Two white PVC vent pipes leaving the top of a condensing tankless water heater and running to a garage wall

Plastic Vent Pipe on Units Listed for It

Condensing heaters are the ones makers list for plastic vent pipe. The code only allows it when the appliance is listed for plastic and the instructions name the exact pipe. Rinnai's RU80i manual lists Schedule 40 PVC, PVC-DWV and Schedule 40 CPVC in 3- and 4-inch sizes, with intake and exhaust ending on the same wall or roof. Condensing units also need a condensate drain. Even Rinnai's non-condensing RL75i and RL94i have a condensate line, which their manual says must be PVC or CPVC and kept off an air conditioner's evaporator coil drain.

  • Listed plastic: Schedule 40 PVC, PVC-DWV, Schedule 40 CPVC (Rinnai condensing unit)
  • Pipe size: 3 or 4 inches on the RU80i; the SENSEI RX spec sheet lists 2- and 3-inch vent
  • Condensate line (Rinnai RL75i/RL94i manual): PVC or CPVC, separate from the A/C drain

See condensing units for the heaters themselves.

Stainless steel vent pipe with a sealed elbow rising from a non-condensing tankless water heater

Metal Vent for Non-Condensing Heaters

A non-condensing heater needs the metal vent its maker lists. Rinnai's manual for its RL75i and RL94i forbids venting with PVC, CPVC, ABS or galvanized pipe and names three tested vent systems: Rinnai/Ubbink Rolux, Heat-Fab Saf-T Vent SC and Metal-Fab Corr/Guard. A different brand's pipe, or a mix of brands, falls outside the listing.

  • Stainless vent, This Old House figure: $400 to $800
  • Horizontal supports every 4 feet, vertical every 6 feet (Rinnai)
  • Vent inspection: at least once a year (Rinnai)
Round vent terminal on a cream stucco garage wall well above the ground and away from a window

Garage Sidewall Terminals and Their Clearances

The whole-house gas units on Rinnai's sizing chart are rated at 160,000 and 199,000 Btu/h, which puts them in the strictest row of Florida's terminal table. On a garage wall, a side window or the driveway can be closer than it looks, so measure before anything is drilled. Rinnai also warns against ending a vent over a walkway or anywhere condensate can cause a nuisance.

  • 12 inches above grade, a porch or a deck
  • Above 150,000 Btu/h: 4 feet minimum below or to the side of an openable window or door, or 1 foot above
  • 50,000 to 150,000 Btu/h: 12 inches from an openable window or door
  • 10 feet sideways from a mechanical air intake, or 3 feet above it
  • 7 feet above a public paved sidewalk or driveway
Gloved hands tightening a brass service valve under a white wall-mounted tankless water heater in a garage

Why Port St. Lucie homeowners and businesses call Port St. Lucie Tankless Water Heater

  • Sending a request is free and doesn't commit you to anything
  • Your details go to one licensed plumber, never a list of callers
  • Ask for the unit's flow rate at your water temperature in writing
  • Ask who files the city permit and books the inspection
  • The referral adds nothing to the plumber's price

Get a free tankless water heater estimate

Free for homeowners and businesses. One local contractor contacts you.

Vent Questions to Settle Before the Quote

No room for a vent run? An outdoor unit exhausts straight from its cabinet, though Rinnai's outdoor manual still sets clearances to windows, doors and air inlets. A Florida plumbing contractor can install the venting under the same license as the gas line (license scope), and tankless units go through the city's permit and plan review, which asks for the maker's specs.

Ask for these in the written quote:

  • Vent material and brand

    Matched to the heater's listing.
  • Run length and elbows

    Inside the manual's limit.
  • Terminal location

    Measured to windows, doors and the driveway.

Ready to get started in Port St. Lucie?

Tell us about the job and a local tankless water heater contractor will get back to you with a free estimate.

Get a free tankless water heater estimate

Free for homeowners and businesses. One local contractor contacts you.